๐Ÿ† National e-Governance Award Winner ยท CC Industry Platform ยท 2019
CC STORIES / TECHNICAL KNOWLEDGE

Technical Knowledge Hub

Practical construction chemical guidance from diagnosis and system selection through application, inspection and maintenance. Browse by technical discipline.

TECHNICAL GUIDE 01

Waterproofing Systems

Terraces, basements, podiums, wet areas and infrastructure

01 ยท Diagnosis & selection

Identify exposure, water pressure, movement and access before selecting a compatible system.

02 ยท Application approach

Check substrate moisture and strength; repair defects; detail penetrations and joints; apply the specified primer and system; protect during curing.

03 ยท QA / QC

Record surface condition, consumption, film thickness where applicable, adhesion and flood testing where suitable.
TECHNICAL GUIDE 02

Concrete Repair

Spalling, honeycombing, cracks and structural rehabilitation

01 ยท Diagnosis & selection

Distinguish cosmetic defects from structural deterioration; investigate corrosion, movement and root causes.

02 ยท Application approach

Remove unsound concrete; clean and treat reinforcement as specified; apply bonding system where required; reinstate with compatible repair mortar.

03 ยท QA / QC

Check substrate preparation, repair depth, curing and required bond/strength tests.
TECHNICAL GUIDE 03

Construction Joints & Sealants

Movement joints, construction joints and penetrations

01 ยท Diagnosis & selection

Determine joint movement, exposure, geometry and compatibility with adjoining membranes.

02 ยท Application approach

Prepare sound clean joint faces; install backing rod or waterstop where designed; prime if specified; apply sealant to required geometry.

03 ยท QA / QC

Inspect continuity, adhesion, joint dimensions and watertightness.
TECHNICAL GUIDE 04

Admixtures & Concrete

Workability, durability, setting and permeability

01 ยท Diagnosis & selection

Review mix design, cement compatibility, aggregate grading, site temperature and performance requirements.

02 ยท Application approach

Carry out laboratory and site trials; follow approved dosing and mixing sequence; monitor fresh concrete properties.

03 ยท QA / QC

Test slump/flow, setting, strength and relevant durability parameters.
TECHNICAL GUIDE 05

Industrial Flooring

Epoxy, polyurethane and cementitious flooring

01 ยท Diagnosis & selection

Assess traffic, chemical exposure, substrate moisture, cracks and slip resistance.

02 ยท Application approach

Prepare concrete mechanically; repair defects; check moisture; apply approved primer, screed and topcoat system.

03 ยท QA / QC

Measure coverage, thickness, adhesion, finish and curing conditions.
TECHNICAL GUIDE 06

Grouts & Anchoring

Machine foundations, baseplates and chemical anchors

01 ยท Diagnosis & selection

Confirm loads, hole geometry, edge distances, vibration and exposure.

02 ยท Application approach

Prepare clean holes and surfaces; install grout or anchor strictly to approved manufacturer procedure.

03 ยท QA / QC

Verify installation records, curing, torque or proof testing where specified.
TECHNICAL GUIDE 07

Technical Specifications

BOQ, method statements and material selection

01 ยท Diagnosis & selection

Define performance, exposure, substrate, service life, compatibility and applicable project standards.

02 ยท Application approach

Prepare a system-specific specification and method statement with materials, sequence, mock-up and hold points.

03 ยท QA / QC

Document acceptance criteria, testing, warranties and maintenance requirements.
TECHNICAL GUIDE 08

Quality Control & Testing

Inspection checklists, site trials and handover

01 ยท Diagnosis & selection

Set inspection and test plans before application and define who signs off each hold point.

02 ยท Application approach

Record batch numbers, ambient conditions, surface preparation, application rate and cure time.

03 ยท QA / QC

Perform relevant inspections and tests and maintain traceable handover records.
Engineering note: These are educational overviews, not project-specific specifications. Final system selection, dosage, thickness, test methods and acceptance criteria must follow approved drawings, applicable standards and current manufacturer technical data sheets.
โ˜Ž